连接器产品规格书

产品规格书PRODUCT SPECIFICATION

[1]合用范畴SCOPE本规格书合用于PIN HEADER系列连接器This specificationcovers the

2.54mm PitchBar Connectorsserise.

[2]产品名称及型号PRODUCT NAMEAND PARTNUMBER产品名称产品型号Product NamePart Number排金十

2.54PH3X3P系列

[3]定格RATINGS项目规格Item Requirement最大容许电压250VRated VoltageMAX[AC有效值rms/DC]最大容许电流

2.0ARated CurrentMAX使用温度范畴-20℃+85℃〜Ambient temperatureRange【4】性能PERFORMANCE

4.1电气性能Electrical Performance项目条件规格Item TestCondition Requirement适合嵌合状态；开放电压如下；短路电流20mV接触电阻10mA的状态下测定W30mContactMAXMate applicable and measureby drycircuit,20mVResistanceMAX,10mA.适合嵌合状态；相邻端子间或端子与地面间加DC绝缘电阻500V下测定^lOOOMQMINInsulation Mateapplicable andapply500V DCbetween adjacentResistanceterminal orground.适合嵌合状态；相邻端子间或端子与地面间加AC耐电压有效值历时分钟下测定无击穿现象500V1Dielectric Mateapplicableandapply1000V ACrms for1No Breakdownminutebetween adjacentterminal orground.

4.2机械性能Mechanical Performance项目条件规格Item TestCondition Requirement端子保持力单端子；以用每分钟的速度平行向25±3mmTerminal外拉

0.8KGFRetention ForcePullthe terminalat thespeed rateof25+3mm perminute公母对插，插入力及拔出力端子插拔力插入力拔W

10.8KGF出力

23.6KGF

4.3环境和其他性能Environmental Performanceand Others项目条件规格Item TestCondition Requirement无通电状态；以次/分钟的速度插拔1020反复插拔接触抵御次RepeatedContactInsertion andwithdrawal catuatorup to2060mInsertion andResistancecyclesat thespeed rateof lessthan10MAXWithdrawalcyclea/minute温度上升适合嵌合状态；最大容许电流通电，温度温度上升Temperature测定UL498Temperature30℃MAXRise RiseCarryingrated currentload.UL498DC1mA通电状态下；嵌合轴沿XYZ三个外观无损坏耐振动性方向振动；振幅；频率

1.5mm10-55-10Hz/Appearance NoDamageVibration分；历时2小时接触抵御60m Amplitude

1.5mm P-P ContactMAXSweeptime10-55-10Hz in1minute Resistance瞬断Duration2hours ineach X.Y.Z.axes1ms.MAX.DiscontinuityDC1mA通电状态下；嵌合轴沿互相垂直无损坏的16个方向;以490m/s2{50G}冲击；各3外观Appearance NoDamage耐冲击性次瞬断Shock1ms.MAX.490m/s2{50G},3strokes ineach X.Y.Z.Discontinuityaxes.外观无损坏435Appearance NoDamage耐热性适合嵌合状态；区空气中；放置接触抵御85±2℃JHeat Resistance60m Q小时；再回到室温中放置小时961-2ContactMAX85±2℃,96hour Resistance外观无损坏Appearance NoDamage耐寒性适合嵌合状态；时空气中；放置-40±2℃接触抵御Cold Resistance60mQ小时；再回到室温中放置小时961-2ContactMAX-40+2℃,96hourResistance外观无损坏适合嵌合状态；、相对湿度40±2℃90-95%Appearance NoDamage的空气中；放置小时；再回到室温中耐湿性96接触抵御60mo小时内测定

0.5Humidity ContactMAXResistanceTemperature40+2℃必须满足

4.

1.3耐电压Relative Humidity90-95%Dielectric Duration96HoursStrength绝缘抵御100MQ MINInsulationResistance适合嵌合状态；分钟；常温常-55±3℃30无损坏温度循环外观湿分钟;分钟；常温常湿Appearance10-1585±2℃30No DamageTemperature分钟，循环次10-155Cycling接触抵御60m Q5cycles ofContactMAXa-55±3℃30minutesResistanceb85±2℃30minutes适合嵌合状态；、勺盐水35±2℃5±1%H无损坏、腐蚀No外观Appearance耐盐雾性喷雾小时；实验后常温水洗；再室48Damage温干燥Salt Spray接触抵御48±4hours exposureto asalt sprayfrom60mQ MAXContactthe5+1%solution at35±2℃.Resistance适合嵌合状态；的40±2℃50±5ppm J接触抵御耐亚硫酸亚硫酸中放置小时2460m QMAXContactSO2Gas24hours exposureto50±5ppm.SO2gas atResistance40±2℃.适合嵌合状态；浓度为的氨水容器28%J外观无损坏耐氨性中；放置分钟40Appearance NoDamageNH3Gas40minutes exposureto NH3gas接触抵御60m Qevapporatingfrom28%Ammonia solutionContactMAXResistance端子前端浸入的锡槽中；历235±5°C时2+

0.5seco可焊性沾敷性沾敷面积以Solder95%Soldering Time2+

0.5sec.上Solderability WettingSoldering Temperature235±5℃

0.2mm fromterminal tip端子前端浸入日勺锡槽中；历260±5℃耐焊接热时5+

0.5seco无损坏、变形NoResistance toSoldering Time5±

0.5sec.外观AppearanceDamageSoldering heatSoldering Temperature260+5℃

0.2mm fromterminal tip）参照规格Reference Standard｝参照单位Reference Unit

[5]外观形状、寸法及材质PRODUCT SHAPE,DIMENSIONS ANDMATERIALS图面参照Refer tothe drawing.名称NAME材质MATERIALS基座Housing PA66PA6T PBTUL94V-0插针Contact C2680备注Remark金属表面镀金。