还剩18页未读,继续阅读
本资源只提供10页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
文本内容:
小区通信设施配套建设工程XX竣工资料建设单位XXXXXXXX施工单位XXXXXXXX年月XXXX XX工程设计变更单工程名称XX通信设施配套建设工程施工单位XXXXXXXX施工地段XXX日期原设计工程量变更设计后工程量变更原因监理单位施工单位工地代表:建设单位工地代表:注本变更单须盖章或签字生效,一式六份,二份交建设单位,四份交施工单位(其中三份作为竣工资料)工程量总表工程名称:序号项目名称单位竣工数量备注1人工开挖路面.混凝土路面(如下)250mm100m22人工开挖路面_水泥花砖路面(如下)_250mm100m23开挖管道沟及人(手)孔坑—一般土100m34回填土方.夯填原土100m35手推车倒运土方.夯填碎石100m36破砌配线手孔_小手孔(ssk)个7安装壁挂式光分派箱箱8架空光(电)缆—工程施工测量100m9管道光(电)缆工—程施工测量100m10GPS定位点11安装宣传警示牌块12架设100米以内辅助吊线条档13敷设管道光缆」2芯如下千米条14敷设管道光缆_36芯如下千米条15打穿楼墙洞/专墙个16打穿楼层洞—混凝土楼层个17增装支承物_终端支承物套18增装支承物—中间支承物套19穿放引上光缆条20架设吊线式墙壁光缆百米条21布放钉固式墙壁光缆百米条22光缆接续」芯如下头223光缆接续芯如下头_2424光缆成端接头芯25皮线光缆直熔芯26如下光缆中继段测试芯如下中继段40km_2427敷设硬质管_如下米PVC e2510028敷设硬质管一
④如下米PVC5010029安装24芯光缆分纤箱架30管、暗槽内穿放光缆百米条31安装光纤连接盘块32光纤跳线一单模条33光纤链路测试_单光纤链路34353637重大工程质量事故汇报通信设施配套建设工程工程名称XXxxx发生事故施工单位XXXXXXXX时间事故情况及主要原工程完工报告工程名称通信设施配套建设工程XXXXX建设地点建设单位XXXXXXXX施工单位XXXXXXXX监理单位计划动工日期实际动工日期计划竣工日期实际竣工日期完毕日勺重要内容本工程布放芯光缆米,布放芯光缆米,布放双芯皮2491012720线光缆米,新设芯壁挂式光交座(详情见图纸或工程量表)48901441提前或推迟的原因详见停、复工告知本工程已于年月日正式竣工,请建设单位交接验收,特此汇报主送(施工单位章)建设单位(章):报送日期工程名称:编号:工程竣工报验单致:(监理单位)我单位已按协议规定完毕了XX通信设施配套建设工程,经自检合格,现报上该工程报验申请表,请予以审查和验收施工单位(章)项目经理审查意见:经初步验收,该工程、符合/不符合我国现行法律、法规规定;
1、符合/不符合我国现行工程建设原则;
2、符合/不符合设计文献规定;
3、符合/不符合施工协议规定;4综上所述,该工程初步验收合格/不合格,可以/不可以组织正式验收项目监理机构_________________________________________监理工程师____________________________________________日期年月一日注本表由施工项目专业质量检查员填写,监理工程师(建设单位项目技术负责人)组织项目专业质量检查员等进行验收工程竣工验收证书(没有模板,自行设计填写)验收测试登记表通信设施配套建设工程验收项目明细检查成果验收内容细则规定合格不合格
1、箱体必须安装牢固,不可松动门锁良好,开关自如
2、箱内走线整洁,信号线与电源线应分走两侧,从不一样出线口走出,并且标识清晰
3、箱体应就近接入大楼或表箱等电位接地点,接地点须通过除锈处理;暴露在室外的接地点须用橡皮泥密封后用自粘胶带包裹
4、箱内设备水平摆放整洁、稳定,必须固定多媒体箱
5、取电可靠,对应连接的楼道电表箱内缆线需有标签示意为移动通信设备用电
6、ONU以太口成端网线到达适合长度、绑扎整洁
7、箱内走线符合设计规定,MDF成端符合设计规范(上线位置、色谱)并接设触良好
8、箱内在用尾纤必须用标签标明上联分光器端口,备用尾纤需标明纤号备
1、箱体必须安装牢固,不可松动门锁良好,开关自如侧配线箱
2、箱内走线符合设计规定,MDF成端符合设计规范(上线位置、色谱)并接触良好标识清晰
1、箱外走线布局美观,楼内同一路由有两根线缆或PVC管时,规定平行、美观(布放整洁、颜色统一)楼道布线
2、楼道槽板或穿线管必须固定牢固,尽量靠近楼道上沿布放
3、需打穿楼板进行垂直布线的工程,孔洞必须封堵
1、光缆进线孔应采用防潮措施,交接箱做好良好接地假如位于路口,应加反光漆保护及警示标志
2、光纤所有接续完毕后应将余纤盘在光纤盘片内,盘绕方向应一致;光缆上光交箱ODF架或者光交箱,走线要美观,标签要规范已布放好欧1光纤,但未启用,光连接头应用保护套保护
3、加强芯要良好接地
1、管井长高宽严格按照设计尺寸,井内缆线布放整洁,光缆预留及接头盒必须贴壁放置
2、管道要符合编号规范规定;编号书写清晰,耐腐蚀;编号要和竣工资料相符自建管道
3、管道深度符合规定,直埋管道过路必须采用混凝土包封,如埋深达不到设计规定必须全程包封线路
4、小区引入段管道建设应尽量靠近楼道口,便于后期光缆接入侧
1、入楼道线缆规范,无飞线,余缆盘放整洁,光缆加强芯与机柜/壁挂箱内接地相连线缆布放及
2、采用墙壁钉固方式布放缆线,必须按规范规定用卡钉固定缆线,卡钉间距相接地似,转角处需套管保护
3、管道引上处必须按照规范规定设置保护管,原则上地上部分室外不不大于
2.5米,室内不不大于
1.5米,并做好管口封堵
4、机架内信号线应应与电源线分开绑扎
5、线缆走线应横平竖直无明显交叉并绑扎固定,拐弯处应均匀圆滑无波折,线缆弯的曲率半径应按客户侧施工规范规定
6、设备接地应与接地柱/条可靠连接,接地柱/条应与保护地或引入的保护地可靠连接,保护地应使用黄绿线,截面积到达设备规定
1、缆线挂牌必须按工程规范制作和放置
2、ODF框、纤芯资料及MDF资料在现场须标识清晰,不意图贴于光交或楼道标识箱门内侧
3、线缆使用光刻塑料旗形标签,标签描述精确、清晰、规范,贴于线缆两端醒目位置接头制作及
1、RJ45水晶头制作符合规范,线缆护套皮应卡入水晶头卡口内线缆连接
2、110高频模块打线符合规范,线缆按色谱卡接整洁,网线在110模块内需要清除护套皮,跳线走线规范整洁,110模块标识精确、完整、清晰收光功率ONU侧日勺收光功率应符合规范规定,并留有一定日勺系统余量性能验收抽测比例为该小区总户数的5%户线可用率到达100%时则验收通过;若测试户线可用率所抽测顾客中不大于10%的户线不可用,则限期3天内整改完毕;若所抽测顾客中户线不可用率超过10%,则认为验收不通过现场环
1、工余料清理,施工现场整洁境
2、设备运行正常,无影响顾客正常工作的噪音建设单位监理单位:施工单位:设计及其他单位:竣工资料建设项目名称通信设施配套建设工程XXXX建设单位XXXXXXXX监理单位:XXXXXXXX施工单位XXXXXXXX编制单位XXXXXXXX资料编制人________________________XXX审核人:XXX隐蔽工程检查记录建设单位施工单位通信设施配套建设工程工程名称XXXX项目栏因此产生如下工作量
1、A栋一层3个、五层至二十层每层6个直经020mm桥架取孔共99个,使用020mm包塑软管99条*
1.5米/条=
148.5米,使用白背板99个使用032mm包塑软管保护5条*
1.5米/条=
7.5米,每个机柜032mm桥架取孔2个.合计;10个032mm接头盒取孔1个
2、B栋一层2个、五层至十五层每层6个直经020mm桥架取孔共68个,使用020mm包塑软管68条*
1.5米/条=
102.0米,使用白背板68个使用032mm包塑软管保护4条*
1.5米/条=
6.0米,每个机柜032mm桥架取孔2个.合计;8个032mm接头盒取孔1个
3、C栋一层3个、
二、三层各1个五层至十八层每层6个直经020mm桥架取孔共89个,使用020mm包塑软管89条*
1.5米/条=
133.5米,使用白背板89个使用032mm包塑软管保护5条*
1.5米/条=
7.5米,每个机柜032mm桥架取孔2个.合计;10个032mm接头盒取孔1个汇总020mm桥架取孔256个使用白背板256个020mm包塑软管256条*
1.5米/条=384米使用032mm包塑软管保护14条*
1.5米/条=21米032mm桥架取孔28个032mm接头盒取孔3个
3、因暗管不通处理暗管赌塞A栋1层至20层合计10处B栋1层至15层合计8处C栋1层至18层合计13处
4、皮线光缆套塑料白管512条管.3米/条=
153.6米
5、分纤箱挂牌14面分纤箱封堵14处18mm钢订线码100个使用玻璃胶1桶6,光缆挂牌49面单盘测试96芯3盘光缆接续24芯如下(带电割熔接)2头24c顾客光缆测试2段跳纤16条(3米)新增24芯接头盒1个,接头盒托架1付负责人监理单位或建设方代表:阐明、项目栏内填写隐蔽工程的种类、规格、尺寸、数量、距离;
1、请详细阐明隐蔽项目的内容,如有必耍请附详细的剖面图或断面图
2、本记录一式叁份,其中一份送监理单位存查,二份由施工单位存查(一份做竣工验收资料)3年月XXXX XX序号名称页次1工程阐明2动工汇报3已安装设备明细表4工程停(复)工汇报5工程变更单6工程材料平衡表7工程量总表8重大工程质量事故汇报9工程交(完)工汇报10工程竣工报验表11工程竣工验收证书12验收测试登记表13竣工图纸14隐蔽工程签证
一、施工根据
1、据XXXX企业的安排;
2、XXXX企业提供的设计图纸;
3、现场查看及搜集有关资料;
二、工程建设概况建设规模
1.1本工程为XXXX通信设施配套建设工程现工程已所有完毕了施工任务,(详情见图纸或工程量表)
三、编制根据竣工图纸经现场勘察丈量绘制工程说明动工汇报工程名称建设地点计划动工日期计划竣工日期建设单位设计单位工程建设有关单位施工单位监理单位各项动工准备已经就绪,动工前培训、质量、技术和安全交底已经完毕,安全生产费已收悉申请于年月日动工施工单位项目经理日期(单位章)经核查,各项动工准备已经就绪,施工组织设计已经通过审查,质量、技术和安全交底已经完毕,施工单位日勺动工前培训已经完毕同意于年月日动工审批意监理单位见总监理工程师日期(单位章)各项动工准备已经就绪,安全生产费已经支付,质量监督申报已经提交同意于年月日动工建设单位项目负责人日期(单位章)单项工程名称通信设施配套建设工程已安装明细表XX序号设备名称及型号单位数量安装地点备注1XXX X XX米2XXX米XXX工程停(复)工报告工程名称建设单位XXXXXXXX通信设施配套建设工程XX施工单位监理单位XXXXXXXX建设地点(地段)XXX停(复)工原因(如没有复工,请在此栏注明)计划停(复)工日期施工单位(章)项目监理机构(章)建设单位(章)项目经理______________总监理工程师________项目负责人___________日期______________日期________日期_________________注本表一式三份,建设单位、监理单位、施工单位各一份。