还剩17页未读,继续阅读
本资源只提供10页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
文本内容:
建筑电焊工练习题+答案
1、手工电弧焊焊接电弧弧柱中心温度一般在()范围内6000-8000oC4000-6000oC2000-4000oC1000-2000oC答案A
2、使用气焊、气割动火作业时,氧气瓶与乙快气瓶与动火作业地点间距不应小于()m并不得在烈日下曝晒A、10B、15C、20D、30答案A使用气焊•气割动火作业时,氧气瓶和乙燃气瓶与动火作业地点间距不应小于()m并不得在烈日下曝晒A、10B、15C、20D、30答案A
4、焊剂分为非熔炼焊剂和熔炼焊剂,下列不属于分类的是()A、iWj硅焊剂B、高氟焊剂C、中硅焊剂D、低硅焊剂答案B
5、安全生产责任制要在()上下真功夫,这是关键的关键A、健全.完善B、分工明确C、贯彻落实D、奖罚兑现答案C
6、墙面等处落地的竖向洞口.窗台高度低于()mm的竖向洞口及框架结构在浇注完混凝土没有砌筑墙体时的洞口,应按临边防护要求设置防护栏杆B、咬边C、夹渣D、再热裂纹答案C
47、电渣压力焊钢筋对接接头偏心和倾斜的主要原因中不正确的是()A、钢筋端部歪扭不直B、焊接工艺参数选择不当C、在夹具中夹持倾斜D、焊后夹具过早放松答案B
48、未焊透是指焊接时接头根部未熔透的现象,下列主要原因中不正确的是()A、电压过大B、电流小C、坡口不合适D、电流大答案D
49、根据《建设工程安全生产管理条例》,为建设工程提供机械设备的单位,应当按照安全施工的要求配备齐全有效的()等安全设施和装置A、保障.限位B、担保.限位C、保险.限制D、保险.限位答案D
50、焊接处()以内不得有可燃、易爆物,工作地点通道宽度应大于1mA、5mB、10mC、15mD、20m答案B
51、起重作业人员高处作业过程工作中,必须佩戴下列哪些劳动防护用品()OA、安全带B、安全帽C、绝缘手套D、防静电服E、防滑鞋答案ABE
52、根据《建设工程安全生产管理条例》规定,出租机械设备和施工机具及配件,应具有()A、生产(制造)许可证B、设备履历书C、产品使用说明书D、产品构造图E、产品合格证答案AE
53、焊丝是()等各种工艺方法的焊接材料A、埋弧焊B、气体保护焊C、电阻焊D、电渣焊E、电气立焊答案ABDE
54、安全标志主要包括()等A、安全标语B、安全色C、安全宣传栏D、安全标志牌E、安全设施答案BD
55、弧坑是收尾时熔池没有填满,或接头时没有结合好留在焊缝表面的凹坑焊缝弧坑缺陷对()有不利的影响A、焊接接头的强度B、应力水平C、焊接接头硬度D、焊接接头化学成分E、金相组织答案AB
56、下列对安全技术交底具体要求的叙述,正确的是()A、各工种的安全技术交底一般与分部分项安全技术交底同步进行B、交底应采用简短的.口号式的形式C、交接底双方应当签字确认D、交底必须具体.明确.针对性强E、交接底应当采用口头形式答案ACD
57、施工单位应当对()每年至少进行一次安全生产教育培训,其教育培训情况记入个人工作档案安全生产教育培训考核不合格的人员,不得上岗A、主要负责人B、项目负责人C、栋号工长D、管理人员E、作业人员答案DE
58、下列哪些属于安全检查噫患整改“三定”原则的内容?()A、定计划B、定人员C、定时间D、定措施E、定落实答案BCD
59、施工企业的从业人员上岗应符合下列要求()必须经安全生产知识和管理能力考核合格,依法取得安全生产考核合格证书A、专职生产安全管理人员B、企业主要负责人C、材料员D、质量员E、项目负责人答案ABE
60、对熔化极氤弧焊,反接时(),使直线电弧周围磁场均匀分布,可防止磁偏吹A、电弧稳B、熔深大C、飞溅大D、焊接电弧不稳E、熔深小答案AB
61、根据《建设施工安全检查标准》(JG59-2011)施工项目大门口处应设置公示牌,主要内容应包括工程概算牌.().管理人员名单及监督电话牌.施工现场总平面图A、安全生产牌B、文明施工牌C、消防保卫牌D、工程责任牌E、工程承诺牌答案BC
62、钢筋气压焊时两钢筋轴线相对偏心量不得大于钢筋直径的
0.15倍,同时不得大于4mm当不同直径钢筋相焊接时,按()计算A、小钢筋直径B、当超过限量时.应切除重焊C、大直径钢筋的
0.35倍D、小直径钢筋
0.35倍E、大钢筋直径答案AB
63、特种作业人员具备的条件为()A、年龄满18岁B、身体健康C、小学以上文化程度.具备相应工种的安全技术知识D、符合相应工种作业特点需要的其他条件E、参加国家规定的安全技术理论和实际操作考核并成绩合格答案ABDE
64、焊接接头形式主要有()4种A、对接接头B、T形接头C、角接接头D、搭接接头E、锁接接头答案ABCD
65、《安全生产许可证条例》规定,企业在()安全生产许可证有效期满时,经原安全生产许可证颁发机关同意,不再审查,安全生产许可证有效期延期3年A、安全生产许可证有效期内B、安全生产许可证有效期外C、发生一起死亡事故D、未发生死亡事故的E、严格遵守有关安全生产的法律法规答案ADE
66、咬边是一种危险性较大的外观缺陷,它不但减少焊缝的承压面积,而且咬边根部往往形成较尖锐的缺口,造成应力集中,很容易形成()A、应力腐蚀裂纹B、应力集中裂纹C、焊缝余高D、宽窄不齐E、焊缝过高.过低答案AB
67、事故噫患泛指生产系统中导致事故发生的()A、人的不安全行为B、自然因素C、物的不安全状态D、客观因素E、管理上的缺陷答案ACE
68、《国务院关于进一步加强企业安全生产工作的通知》要求,要加强安全培训机构管理,定期公布安全培训机构名单和培训范围,接受社会监督,支持()等开展安全培训A、高等学校B、技工院校C、职业院校D、农民工业余学校E、工会培训机构答案BE
69、下列关于起重吊装安全技术要求,说法正确的是A、吊索系挂点应符合专项施工方案要求B、起重机作业时起重臂下.不得有人停C、起重机作业时.吊物不得从人正上方通过D、起重机吊具可低速载运人员E、吊运易散落物件应使用专用吊笼答案ABCE
70、E4303碳钢焊条型号表示的意思()A、焊条药皮为钛钙型B、可用交流或直流正.反接焊接C、焊条适用于全位置焊接D、熔敷金属抗拉强度ab》420MPaE、焊丝答案ABCD
71、固定动火作业场应布置在可燃材料堆场及其加工场.易燃易爆危险品库房等全年最小频率风向的上风侧A、正确B、错误答案A
72、应急预案是规定事故应急救援工作的全过程A、正确B、错误答案A
73、焊接变形的矫正一般分为机械矫正法,火焰矫正法A、正确B、错误答案A
74、焊接变形从工艺上可以采用反变形、刚性固定法、选择合理的焊接参数和装配次顺序A、正确B、错误答案A
75、在准备焊接时,焊接电缆可以尽量长,可以根据工作时的具体情况而定A、正确B、错误答案B
76、GB/T5117-1995碳钢焊条中,规定的焊条型号编制方法是前两位数字表示熔敷金属抗金属抗拉强度的最大值A、正确B、错误答案B
77、建筑起重机械上,在能安全使用的基础上,可以安装非原制造厂制造的标准节和附着装置A、正确B、错误答案B
78、焊接变形从设计上可以采用选用合理焊缝尺寸和形状、尽可能减少焊缝数量、合理安排焊缝位置A、正确B、错误答案A
79、各种焊材中均含有不同数量的镒,因为镒不易挥发,因此焊工不会造成锈中毒A、正确B、错误答案B
80、《建设工程安全生产管理条例》规定,工程监理单位在实施监理过程中,发现存在安全事故隐患情况严重的,应当立即向有关主管部门报告A、正确B、错误答案B
81、特种作业人员必须按照国家有关规定,经过专门的安全作业培训,并取得特种作业操作资格证书后,方可上岗作业A、正确B、错误答案A
82、施工单位应当制定本单位生产安全事故应急救援预案,建立应急救援组织或者配备应急救援人员,配备必要的应急救援器材.设备,并定期组织演练A、正确B、错误答案A
83、对于碳钢和低合金钢,一般应按照钢材的强度等级选用焊条,同时还应综合考虑焊缝的塑性、韧性A、正确B、错误答案A
84、焊接设备出现故障时应立即切断电源,焊工应立即进行修理A、正确B、错误答案B
85、建设工程实行施工总承包的,一旦发生安全事故,施工总承包单位应当负起及时报告的义务A、正确B、错误答案A
86、电光性眼炎发病有一段潜伏期,往往在接收紫外线照射后6-8小时内发病A、正确B、错误答案A
87、深入开展以岗位达标专业达标和企业达标为内容的安全生产标准化建设,凡在规定时间内未实现达标的企业要依法暂扣其生产许可证,责令停产整顿,对整改逾期未达标的,地方政府依法予以关闭A、正确B、错误答案A
88、根据《建设工程安全生产管理条例》,实行施工承包的由总承包单位统一编制建设工程生产安全事故应急救援预案分包单位不需配备应急救援人员A、正确B、错误答案B
89、酸性焊条是药皮中含有较多酸性氧化物的焊条,这类焊条的工艺性能好,其焊缝外表成形美观、波纹细密A、正确B、错误答案A
90、固定动火作业场应布置在可燃材料堆场及其加工场、易燃易爆危险品库房等全年最小频率风向的上风侧A、正确B、错误答案AA、300B、500C、800D、1000答案C
7、()是建筑施工企业最基本的安全生产管理制度A、安全生产责任制度B、安全检查制度C、安全技术交底制度D、安全教育制度答案A
8、建设工程项目应当配备专职安全生产管理人员,其中5万平方米以上的建筑工程,装饰工程至少应配备()专职安全生产管理人员A、1名B、2名C、3名D、4名答案C
9、焊接接头中延迟裂纹最大的危险是可能引起()A、接头塑性断裂B、接头脆性断裂C、接头硬度升高D、对焊接接头影响不大答案B
10、职工或者其近亲属认为是工伤,用人单位不认为是工伤的,由()承担举证责任A、用人单位B、职工C、政府D、近亲属答案A
11、《国务院关于进一步加强企业安全生产工作的通知》要求,要进一步规范企业生产经营行为加强对生产现场监督检查,严格查处()的“三违”行为A、违章生产.违章指挥.违反劳动纪律B、违章生产.违章指挥.违法操作规程C、违章作业.违章指挥.违法操作规程D、违章作业.违章指挥.违反劳动纪律答案D
12、施工单位应当在施工现场入口处.施工起重机械.临时用电设施.脚手架.出入通道口.楼梯口.电梯井口.孔洞口.桥梁口.隧道口.基坑边沿.爆破物及有害危险气体和液体存放处等危险部位,设置明显的()A、安全提示标志B、安全宣传标志C、安全指示标志D、安全警示标志答案D
13、根据《建筑企业职工安全培训教育暂行规定》的要求,企业法人代表.项目经理教育和培训的时()A、5学时B、30学时C、60学时D、90学时答案B
14、《建设工程安全生产管理条例》规定,()负责对安全生产进行现场监督检查A、专职安全生产管理人员B、工程项目技术人员C、工程项目施工员D、项目负责人答案A
15、根据《安全色》规定,安全色分为红.黄.蓝.绿四种颜色,分别表示()OA、禁止.指令.警告和提示B、指令.禁止•警告和提示C、禁止.警告.指令和提示D、提示.禁止.警告和指令答案C
16、对于实芯焊丝,以H08MnA为例,其牌号表示方法为字母“H”表示A、焊丝B、焊条C、焊机D、焊剂答案A
17、垂直运输机械作业人员.安装拆卸工.爆破作业人.起重信号工.登高架设作业人员等特种作业人员,必须按照国家有关规定经过()培训,并取得特种作业操作资格证书后,方可上岗作业A、专门的安全作业B、三级教育C、安全教育D、安全技能答案A
18、根据《建设工程安全生产管理条例》,设计单位和注册建筑师等注册执业人员应当对其()负责A、资质B、企业C、设计D、行为答案C
19、以下选项中的属于可燃性气体的是()A、氮气B、一氧化碳气C、氧气D、二氧化碳答案B
20、乙燃瓶解冻时可采用()方式A、用小火烧烤B、用温水沐浴C、用榔头敲击瓶体D、上冻瓶体报废处理答案B
21、电阻焊机是指采用()原理进行焊接的一种设备A、电阻加热B、电容加热C、电感加热D、电弧加热答案A
22、施工单位应当自施工起重机械和整体提升脚手架.模板等自升式架设设施验收合格之日起()内,向建设行政主管部门或者其他有关部门登记A、15日B、20日C、30日D、40日答案C
23、建设工程施工前,施工单位()应当对有关安全施工的技术要求向施工作业班组.作业人员作出详细说明,并由双方签字确认A、专职安全生产管理人员B、负责项目管理的技术人员C、负责项目管理的安全生产管理人员D、项目负责人答案B
24、根据《建筑业企业资质管理规定》(建设部令第87号)和《建筑业企业资质等级标准》的规定,从事施工起重机械安装.拆卸施工的单位,应当具备()OA、特种设备安装改造维修许可证B、起重设备安装工程专业承包资质C、塔式起重机拆装许可证D、起重机械安装许可证答案B
25、()自事故发生之日起30日内,事故造成的伤亡人数发生变化的,应当及时补报A、道路交通事故B、火灾事故C、建筑工程事故D、所有事故答案C
26、根据《建设工程安全生产管理条例》规定,达到一定规模的危险性较大的分部分项工程应编制专项施工方案,经施工单位技术负责人和()签字后实施A、业主代表B、设计主持人C、总监理工程师D、有关部门答案C
27、对于实芯焊丝,以H08MnA为例,其牌号表示方法为尾部标有“A”或“E”时,分别表示为()“优质品”或“高级优质品”表明S、P含量更低A、“优质品”或“高级优质品”B、次品C、普通产品D、进口产品答案A
28、当乙快漏气着火时,下列不能用于灭火的是()A、干粉B、二氧化碳C、四氯化碳D、氮气答案C
29、《建设工程安全生产管理条例》规定,建设单位在编制工程()时,应当确定建设工程安全作业环境及安全施工措施所需的费用A、施工预算B、施工方案C、概算D、决算答案C
30、上级人民政府认为必要时,可以调查由下级人民政府负责调查的事故自事故发生之()日起日内(道路安全事故.火灾事故自发生之日起7日内),原事故伤亡人数变化导致事故等级发生变化,依照条例规定应道由上级人民政府负责调查的,上级人民政府可以另行组织事故调查组进行调查A、30B、10C、45D、20答案A
31、以下哪项属于人的不安全行为()A、以手代替工具操作B、攀坐安全位置C、行走安全通道D、不冒险进入危险场所答案A
32、安全防护设施的验收应按类别逐项检查,()后方可使用,并应作出验收记录A、移交B、转移C、验收D、交底答案C
33、《建设工程安全生产管理条例》规定,施工单位的项目负责人应根据工程的特点组织制定安全施工措施,消除安全事故口急患,()报告生产安全事故A、及时.如实B、调查清楚后C、准时.真实D、及时.全面答案A
34、人本管理就是在企业管理活动中,必须把()放在首位,体现以人为本的指导思想A、人的因素B、物的因素C、材料的因素D、环境的因素答案A
35、安全技术交底应()A、全面有针对性B、编写一份存档即可C、可不填写时间D、交底人可以不签字答案A
36、雨天和雪天进行高处作业时,必须采取可靠的防滑.防寒和()措施A、防霜B、防水C、防雾D、防冻答案D
37、根据建设部的有关规定,建筑施工企业项目负责人,是指由()授权负责建设工程项目管理的负责人A、企业总经理B、企业董事会C、企业劳动人事部门D、企业法定代表人答案D
38、()在申请领取施工许可证时,应当提供建设工程有关安全施工措施的资料A、施工单位B、建设单位C、项目负责人D、监理公司答案B
39、施工单位应当在施工组织设计中编制安全技术措施和施工现场临时用电方案,对基坑支护与降水工程.土方开挖工程.模板工程.起重吊装工程.脚手架工程.拆除.爆破工程达到一定规模的危险性较大的分部分项工程编制专项施工方案,并附具(),经施工单位技术负责人.总监理工程师签字后实施,由专职安全生产管理人员进行现场监督A、安全用电方案B、安全实施方案C、安全施工方案D、安全验算结果答案D
40、气瓶(乙焕瓶.氧气瓶)与焊炬相互间的距离不应小于()moA、5B、10C、15D、20答案B
41、气保焊焊接时,焊丝卡在导电嘴中不能顺畅送出时应()A、用手抠除导电嘴附近杂物B、摘下焊接面罩查看导电嘴内是否有异物堵塞C、将耳朵贴近导电嘴附近听听是否有杂物卡壳声音D、关闭电源.拆开导电嘴,清理干净后,组装好在重新打开电源答案D
42、根据《建筑施工临时支撑结构技术规范》JGJ300・2013的要求,模板支撑结构中支撑结构顶端可调托撑伸出长度不应超过(),插入立杆内的长度不应小于()300mm;150mm150mm;300mm250mm;100mm100mm;250mm答案A
43、建筑施工企业应当建立企业负责人及()施工现场带班制度,并严格考核A、技术负责人B、安全负责人C、经营负责人D、项目负责人答案D
44、焊接场所应设有(),防止焊接烟尘和有害气体对焊工造成危害A、通风除尘设施B、焊接设备C、防弧光辐射设施D、消防设施答案A
45、根据建设部的有关规定,施工单位()的工人,必须接受三级安全培训教育,经考核合格后,方能上岗A、转岗B、新入场C、变换工种D、从事特种作业答案B
46、在焊接过程中,焊接电瓶电流过小时,会产生未焊透、气孔及()等A、焊瘤。